wvdial.conf
WVDIAL.CONF(5) WvDial WVDIAL.CONF(5)
NAME
wvdial.conf - wvdial configuration file
DESCRIPTION
When wvdial starts, it first loads its configuration from
/etc/wvdial.conf, which contains basic information about the modem
port, speed, and init string, along with information about your Inter-
net Service Provider (ISP), such as the phone number, your username,
and your password.
The configuration file /etc/wvdial.conf is in Windows "ini" file for-
mat, with sections named in square brackets and a number of variable =
value pairs within each section.
Here is a sample configuration file:
[Dialer Defaults]
Modem = /dev/ttyS2
Baud = 57600
Init = ATZ
Init2 = AT S11=50
Phone = 555-4242
Username = apenwarr
Password = my-password
[Dialer phone2]
Phone = 555-4243
[Dialer shh]
Init3 = ATM0
[Dialer pulse]
Dial Command = ATDP
The sample configuration file above contains all of the options neces-
sary to run the two sample command lines given above. Here is a com-
plete list of settings that wvdial understands:
Modem The location of the device that wvdial should use as your
modem. The default is /dev/modem.
Baud The speed at which wvdial will communicate with your modem.
The default is 57600 baud.
Init1 ... Init9
wvdial can use up to nine initialization strings to set up your
modem. Before dialing, these strings are sent to the modem in
numerical order. These are particularly useful when specifying
multiple sections. See above for an example that uses Init3 to
turn the modem’s speaker off. The default is "ATZ" for Init1.
Phone The phone number you want wvdial to dial. You can add up to 4
other phone numbers that wvdial will dial in order, by adding:
Phone1
Phone2
Phone3
Phone4
Dial Prefix
wvdial will insert this string after the dial command and
before the phone number. For example, to disable call waiting
(in North America, anyway) set this to "*70,".
Dial Command
wvdial will use this string to tell the modem to dial. The
default is "ATDT".
Login You must set this to the username you use at your ISP.
Login Prompt
If your ISP has an unusual login procedure that wvdial is
unable to figure out, you can use this option to specify a
login prompt. When this prompt is received from your ISP,
wvdial will send the Login string.
Password
You must set this to the password you use at your ISP.
Ask Password
By setting this option wvdial will prompt for your password on
every dialin. Thus you don’t have to save your password in
/etc/wvdial.conf. (Option added by SuSE.)
Password Prompt
If your ISP has an unusual login procedure that wvdial is
unable to figure out, you can use this option to specify a
password prompt. When this prompt is received from you ISP,
wvdial will send the Password string.
PPPD Path
If your system has pppd somewhere other than /usr/sbin/pppd,
you will need to set this option.
Auto DNS
Try to get the Domain Nameserver (DNS) from the provider. This
option is "on" by default. (Option added by SuSE.)
Check DNS
Check the Domain Nameserver (DNS) after the connection has been
set up. This option is "on" by default. (Option added by
SuSE.)
DNS Test1
First DNS lookup for DNS check. (Option added by SuSE.)
DNS Test2
Second DNS lookup for DNS check. (Option added by SuSE.)
Check Def Route
Check the default route after the connection has been set up.
This option is "on" by default. (Option added by SuSE.)
Force Address
This option only applies if you have a static IP address at
your ISP, and even then you probably don’t need it. Some ISP’s
don’t send the IP address as part of the PPP negotiation. This
option forces pppd to use the address you give it.
Remote Name
If your ISP uses PAP or CHAP authentication, you might need to
change this to your ISP’s authentication name. In most cases,
however, it’s safe to use the default value, "*".
Carrier Check
wvdial checks your modem during the connection process to
ensure that it is actually online. If you have a weird modem
that insists its carrier line is always down, you can disable
the carrier check by setting this option to "no".
Stupid Mode
When wvdial is in Stupid Mode, it does not attempt to interpret
any prompts from the terminal server. It starts pppd immedi-
ately after the modem connects. Apparently there are ISP’s
that actually give you a login prompt, but work only if you
start PPP, rather than logging in. Go figure. Stupid Mode is
(naturally) disabled by default.
New PPPD
You need this option if you have pppd version 2.3.0 or newer,
to make wvdial create the file /etc/ppp/peers/wvdial. This
option is enabled by default, thus if you have older pppd you
need to set it to ‘no’ (or upgrade pppd).
Default Reply
When wvdial detects a prompt, and it hasn’t seen any clues that
indicate what it should send as a response to the prompt, it
defaults to sending "ppp". Sometimes this is inadequate. Use
this option to override wvdial’s default prompt response.
Auto Reconnect
If enabled, wvdial will attempt to automatically reestablish a
connection if you are randomly disconnected by the other side.
This option is "on" by default.
Idle Seconds
Set the hangup timeout in seconds. If there is inactivity for
the given time the connection is shut down. A hangup timeout
of 0 disables this feature.
Abort on Busy
If enabled, wvdial will not retry the connection if the modem
says that the line is busy. This option is "off" by default.
Abort on No Dialtone
If enabled, wvdial will not retry the connection if the modem
says that there is no dialtone. This option is "on" by
default.
Dial Attempts
If value is set, wvdial will quit after that many tries .If set
to 0, wvdial will happily keep dialling forever.
The wvdialconf(1) program can be used to detect your modem and fill in
the Modem, Baud, and Init/Init2 options automatically.
SEE ALSO
wvdial(1), wvdialconf(1), pppd(8).
AUTHORS
Dave Coombs and Avery Pennarun for Net Integration Technologies Inc.,
as part of the Worldvisions Weaver project. Greatful contributions
have been made by many people, including SuSE and RedHat. Thanks Guys!
Debian Project December 1999 WVDIAL.CONF(5)
